Maintenance Sign-Up

 

 

Here down the page yow will discover a bunch of very good details involving A Step-by-Step Guide to Installing a Bathtub.

Setting up a bath tub isn't exactly rocket science, however it does call for solid plumbing, carpentry, and also sometimes, tiling skills. Changing an old bath tub with a new one is likewise a reasonably hard project. If the old tub is conveniently accessible, the project can move immediately; if you need to open a wall to eliminate the old bathtub and also position the new tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly require an assistant to vacate the old tub and set in the new one. Make certain you have actually certified yourself for the job and are comfortable trying it. Instead of hiring a specialist to take control of a halfway-completed task, it is better to consider employing one before you begin. Chances are you may need an expert plumber to make tube connections.
This post will certainly assist you mount a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub and also do not require to transform the setup of your previous water pipelines.
Your devices and also product checklist should comprise the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipeline Caps


 

Removing Old Taps

If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you ought to do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any type of water staying in the system. The process of removing the existing taps can be fairly bothersome as a result of the restricted gain access to that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth ready for the continuing to be water that will certainly come from the pipes. As soon as the supply pipelines have been removed, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning throughout this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Before going on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.

 

 

Suitable New Touches

If the tails of the new faucets are plastic, then you will require a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will require minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin ensuring that the washing machines are in location between the faucet and the sink. Protect the tap in position with the manufacturer supplied backnut. Once the faucet is securely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap ports. The previous type needs to be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.

 

 

Installing the Bath tub

Using the two wood boards under its feet, place the tub in the called for position. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four tiny factors.
The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by examining the level and adjusting the feet on the tub up until the level reads level.
To set up faucets, fit all-time low of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the same for the other tap.
Turn on the water and check all joints as well as brand-new pipework for leakages and tighten them if necessary. Fill up the tub as well as additionally check the overflow outlet as well as the typical electrical outlet for leakages.
Ultimately, fix the bath paneling as described in the maker's user's manual. Tiling and also securing around the bath tub should wait until the bathtub has been utilized a minimum of when as this will certainly resolve it right into its last placement.

 

 

Getting ready for the Installation

First of all, the supporting framework supplied with the bath must be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to make certain that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its final placement.

 

 

Tiling Around the Tub

In the area where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to break a rigid seal, creating the water to permeate the wall in between the bath and the tiling, causing problems with wetness as well as possible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and can securing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealant can split fairly very early if you do not take into account this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly available on the market. It is suggested to fit the tiles making use of water-resistant or water resistant glue and cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Hopefully you liked our part about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks a lot for taking the time to read our post. Are you aware of somebody who is involved in the topic? Be sure share it. Thanks a bunch for your time. Visit us again soon.

Free Estimate